PERMAGLAZE II

HIGH PERFORMANCE, HIGH GLOSS, CHEMICAL AND ABRASION RESISTANT EPOXY-POLYESTER COATING. 

DESCRIPTION:

PERMAGLAZE II IS A HYBRID COATING THAT COMBINES THE BEST PROPERTIES OF EPOXIES AND POLYESTERS.  A DURABLE, HARD “GLAZED TYPE” FINISH SUITABLE FOR INTERIOR OR EXTERIOR IS ACHIEVED.  USED ON CONCRETE FLOORS, AS A HIGH PERFORMANCE WALL COATING OR AS A RE-GLAZING COMPOUND FOR BATH FIXTURES.

ADVANTAGES:

·  CURES TO A HARD, TOUGH ABRASION AND CHEMICALLY-RESISTANT FILM.

·  OUTSTANDING HIGH GLOSS RETENTION.

·  EXCELLENT COLOR RETENTION-RESISTANT TO FADING.

·  IMPERVIOUS TO MOST ACIDS, ALKALI, SOLVENTS, OIL, GREASE, BRINE AND CAUSTICS.

SURFACE PREPARATION:

CONCRETE & MASONRY:  ON STEEL-TROWELED SMOOTH CONCRETE THIN THE FIRST COAT UP TO 50% WITH TOPSOLV 100 MANUFACTURED BY E.L.S. PRODUCTS CORP. FOR DEEPER PENETRATION.  ON ABSORBENT CONCRETE OR MASONRY, USE PERMAGLAZE PRIMER TO PRIME THE SURFACE BEFORE APPLICATION OF GLAZE COATS. 

PORCELAIN BATH ITEMS: 

ETCH PORCELAIN WITH DILUTED HYDROFLORIC ACID AND RINSE WITH AMMONIA WATER.  WHEN DRY, APPLY PERMAGLAZE PRIMER AND THEN PERMAGLAZE II.

STEEL: SURFACES SHOULD BE SANDBLASTED BEFORE APPLICATION OF GLAZE COATS.  (ZINC RICH PRIMER SHOULD BE USED WHEN EXTREME CORROSIVE ENVIRONMENT EXIST). 

MIXING:

PERMAGLAZE II IS A TWO-COMPONENT SYSTEM WHICH IS MIXED TOGETHER IN EQUAL VOLUMES AND ALLOWED TO SET 30 MINUTES BEFORE APPLICATION. 

APPLICATION:

APPLY ONLY TO CLEAN, DRY GREASE-FREE SURFACES.  SPRAY APPLICATION IS BEST BUT NATURAL BRISTLE BRUSH OR SHORT NAP ROLLER MAY BE USED.  TWO COATS ARE RECOMMENDED FOR OPTIMUM RESULTS. 

IMPORTANT: APPLY PERMAGLAZE II IMMEDIATELY WHEN PRIMER HAS BECOME TACKY.

DO NOT WAIT MORE THAN 24 HOURS BETWEEN COATS UNLESS ABRADED.  

PHYSICAL PROPERTIES:

                                                                                                        RESULTS                     FEDERAL TEST

                                                                                                                                                STANDARD#141a

HARDNESS, SWARD                                                                                                        (4.3.11)

1 DAY                                                                                                    20

7 DAYS                                                                                                  44

14 DAYS                                                                                                50

HARDNESS, TUKON

7 DAYS                                                                                                  10.2

14 DAYS                                                                                                12.7

HIDING POWER (MINIMUM CONSTANT RATIO)                    0.94                         4122

GLOSS, 60 DEGREES SPECULAR                                                     97                            6101

REFLECTANCE, DIRECTIONAL MINIMUM                              86                            6121

IMPACT FLEXIBILITY, MINIMUM INCH-LBS                             24                            6226

FLEXIBILITY 1/8” MANDEEL BEND                                              PASS                      6221

ABRASION RESISTANCE, MAX WT. LOSS (MG)                      75                            6192

YELLOWNESS ACCELERATED,

MAXIMUM YELLOWNESS INDEX INCREASE                           0.10                         6131

PACKAGING:

2 GAL UNITS CONTAINING 1-1 GAL PERMAGLAZE II MIX A 1-1 GAL PERMAGLAZE II MIXB

10 GAL UNITS CONTAINING 1-5 GAL PERMAGLAZE II MIX A 1-5 GAL PERMAGLAZE II MIX B

COVERAGE:

PERMAGLAZE II WILL COVER 250 TO 350 SQ. FT. PER GALLON DEPENDING ON THE SURFACE AND METHOD OF APPLICATION.

CLEAN - UP:

CLEAN TOOLS AND EQUIPMENT IMMEDIATELY AFTER USE WITH TOPSOLV 100 MANUFACTURED BY E.L.S. PRODUCTS CORP.