|
HIGH GLOSS, LOW ODOR, VOC COMPLIANT EPOXY WALL COATING.
DESCRIPTION:
PERMAGLAZE WB IS AN ADVANCED FORMULA TWO COMPONENT EPOXY
AMINE COATING SYSTEM. THIS MATERIAL IMPARTS
A TILE-LIKE GLOSS FINISH WITH PERFORMANCE CHARACTERISTICS OF CONVENTIONAL EPOXY
SOLVENT BASED SYSTEMS. PERMAGLAZE WB IS
APPROPRIATE FOR USE ANY WHERE A WASHABLE, DURABLE, CHEMICAL RESISTANT WALL, CEILING
OR ALL PURPOSE COATING IS NECESSARY.
ADVANTAGES:
·
EXTREMELY LOW ODOR
·
NON - FLAMMABLE
· TILE LIKE FINISH
· COMPATIBLE
WITH A WIDE RANGE OF PRIMERS OR PREVIOUS COATING
· EXCELLENT ADHESION TO STEEL, OTHER METALS
· 4 TO 6 HOURS WORKING TIME
· SOAP AND WATER CLEAN UP
PHYSICAL PROPERTIES:
EPOXY / AMINE
FED. TEST METHOD
FLEXIBILITY 1/8” MANDREL
PASS
141,6221
TACK FREE TIME, HRS @ 77 DEGREES F.
2-3
141,4061
HARDNESS, PENCIL, 24 HOURS
2B
ASTM D - 3363
7 DAYS
2H
-----------
SWARD, 7 DAYS
30-40
ASTM D - 2134
ABRASION RESISTANCE,
TABER CS - 17 WHEEL
50-60
141,6192
500 GM. LOAD, 1000 CYCLES, MG LOSS
FALLING SAND, LITERS/MIL
60-65
141,6191
SCRUB RESISTANCE
1000 OSCILLATIONS
PASS
141,6142
FIRE RESISTANCE
------
ASTM E - 162
FLAME SPREAD
0
FUEL CONTRIBUTES
0-2
SMOKE DEVELOPED
0-3
SALT SPRAY RESISTANCE, 500 HOURS
PASSED
141,6061
FREEZE THAW RESISTANCE, 50 CYCLES
PASSED
----------
SURFACE PREPARATION:
ALL SURFACES TO RECEIVE PERMAGLAZE WB SHOULD BE FREE OF GREASE,
OIL, LAITENANCE OR OTHER SURFACE CONTAMINANTS.
PREVIOUSLY PAINTED SURFACES SHOULD BE SOUND AND CLEAN.
TECHNICAL SERVICE IS AVAILABLE FROM E.L.S. PRODUCTS CORP.
CEMENT BLOCK SHOULD BE PRIMED WITH PERMABLOCK MANUFACTURED BY E.L.S PRODUCTS
CORP. 1 DAY PRIOR TO APPLICATION OF PERMAGLAZE WB. SHEETROCK, CEMENT WALLS, OR
PLASTER SHOULD BE PRIMED WITH BASECOTE MANUFACTURED BY E.L.S. PRODUCTS CORP. 1
DAY PRIOR TO APPLICATION OF PERMAGLAZE.
STEEL OR METAL SHOULD BE PRIMED WITH Z-500 ZINC PRIMER MANUFACTURED BY
E.L.S. PRODUCTS CORP.
MIXING:
THOROUGHLY STIR PERMAGLAZE WB MIX A AND PERMA WB MIX B TO
REDISTRIBUTE ANY INGREDIENTS THAT HAVE SETTLED DURING SHIPPING.
COMBINE EQUAL PROPORTIONS OF PERMAGLAZE WB MIX A AND PERMAGLAZE WB MIX
B. THE MIX RATIO IS 1 PART MIX A TO 1
PART MIX B. PERMAGLAZE WB HAS AN EXTENDED
POT LIFE AND MAY BE USED DURING A 4 TO 6-HOUR PERIOD AFTER MIXING.
MIXED MATERIAL OVER 8 HOURS OLD MAY STILL BE FLUID BUT SHOULD NOT
BE APPLIED.
APPLICATION:
AFTER MIXING, PERMAGLAZE WB MAY BE APPLIED BY SPRAY, ROLLER
OR BRUSH. TWO COATS OVER A PROPERLY PRIMED
SURFACE WILL YIELD MAXIMUM RESULTS. CURING
IS ACCELERATED AT HIGH TEMPERATURES AND RETARDED IN LOW TEMPERATURES.
DO NOT APPLY WHEN AIR OR SURFACE TEMPERATURE IF BELOW 38 DEGREES F.
APPLICATION IN HIGH HUMIDITY ENVIRONMENTS MAY RESULT IN SOME DULLING OF
THE “GLAZE”. THIN MIXED SYSTEM 5 TO 10%
WITH WATER TO FACILITATE SPRAYING. DO
NOT ADD ANY OTHER CHEMICALS OR SOLVENTS TO THE MIXED MATERIAL.
CLEAN - UP:
CLEAN UP TOOLS AND EQUIPMENT IMMEDIATELY AFTER USE WITH SOAP
AND WATER.
COVERAGE:
PERMAGLAZE WB
~ 250 - 300 SQ.
FT PER GALLON*
PERMA BLOCK
~ 75 - 100 SQ.
FT PER GALLON*
BASECOTE
~ 150 - 400 SQ. FT. PER GALLON*
Z-500
~ ZINC PRIMER 350 - 500 SQ. FT. PER GALLON*
*APPROXIMATE DEPENDING ON SUBSTRATE CONDITION AND METHOD
OF APPLICATION.
PACKAGING:
2 GAL UNITS CONTAINING
1-1 GAL PERMAGLAZE WB MIX A
1-1 GAL
PERMAGLAZE WB MIX B
10 GAL UNITS CONTAINING
1-5 GAL PERMAGLAZE WB MIX A
1-5 GAL PERMAGLAZE WB MIX
B
|
