|
HYDROSHIELD WB
LOW ODOR, VOC
COMPLIANT, CLEAR, NON-GLOSS PROTECTIVE COATING TO SEAL CONCRETE, MASONRY
OR STUCCO.
PURPOSE:
HYDROSHIELD WB
HAS BEEN PRIMARILY DESIGNED TO SEAL MASONRY WALLS, CONCRETE SLABS, DECKS,
WALLS, AND ABUTMENTS FROM BOTH WATER AND CHLORIDE INTRUSION WHILE
PROVIDING FOR WATER VAPOR TRANSMISSION (BREATH ABILITY)
HYDROSHIELD WB
IS A SOLVENT FREE SILANE MODIFIED SILOXANE WHICH CHEMICALLY BONDS TO THE
SUBSTRATE. THE HIGHLY HYDROPHOBIC CHEMICAL MOLECULES ARE EXTREMELY SMALL
(17A) RESULTING IN PENETRATION DEPTHS OF 1/4 OF AN INCH. THIS MATERIAL IS
UV RESISTANT AND WILL NOT TURN YELLOW, AND PROVIDES A BARRIER TO
DESTRUCTIVE CARBONATION.
ADVANTAGES:
l MARKEDLY REDUCES WATER AND CHLORIDE INTRUSION
l BREATHABLE PROVIDING FOR WATER VAPOR TRANSMISSION
l
CHEMICALLY RESISTANT TO ICE MELTING COMPOUNDS, FUELS, OILS AND
ATMOSPHERIC CONTAMINANTS
l INHIBITS EFFLORESCE
l
INCREASES FREEZE-THAW RESISTANCE
l PREVENTS STAINING AND DISCOLORATION DUE TO
ELECTROSTATIC ATTRACTION OF DUST PARTICLES
l CAN BE APPLIED TO DAMP SURFACES
l
DEEP PENETRATION INTO SUBSTRATE
l PROVIDES A BARRIER TO DESTRUCTIVE CARBONATION
l TREATED SURFACE CAN BE PAINTED
SURFACE
PREPARATION:
THE SUBSTRATE SHOULD
BE STRUCTURALLY SOUND AND FREE OF GREASE, OIL, SEALERS, COATINGS OR OTHER
SURFACE CONTAMINANTS. HYDROSHIELD WB MAY BE APPLIED TO DAMP SURFACES
PROVIDED NO SURFACE LIQUID EXISTS.
APPLICATION:
MIX MATERIAL TO
REDISTRIBUTE ANY SETTLED INGREDIENTS. APPLY DIRECTLY FROM THE CAN, WITH
NO THINNING. THE PRIME COAT OF THE HYDROSHIELD WB SHOULD BE ALLOWED TO
DRY AT LEAST ½ HOUR BEFORE THE TOP COAT IS APPLIED. APPLY MATERIAL ON
WALLS IN A FLOOD COAT TO SATURATION STARTING AT THE TOP AND WORKING DOWN.
PROTECT WINDOWS FROM OVER SPRAY. ON DECKS APPLY AT SUGGESTED COVERAGE
RATES.
APPLICATION COVERAGE
PRIME
COAT..........................................................................................100
SQ. FT PER GALLON
TOP
COAT...............................................................................................200
SQ. FT PER GALLON
PRODUCT MAY BE EITHER
SPRAYED OR ROLLER APPLIED.
APPEARANCE:
THE HYDROSHIELD WB
SYSTEM WILL SLIGHTLY DARKEN THE SURFACE OF THE SUBSTRATE IT IS APPLIED TO.
HYDROSHIELD WB WILL NOT ALTER EITHER THE COLOR OR TEXTURE OF THE SURFACE.
ADHESION OF
SEALANTS:
ALL CONTROL, CRACK AND
EXPANSION JOINT SEALING SHOULD BE DONE PRIOR TO THE APPLICATION OF THE
HYDROSHIELD WB.
APPLICATION:
DO NOT APPLY HYDROSHIELD
WB SYSTEM WHEN THE AIR OR SURFACE TEMPERATURE OF BELOW 38 DEGREES F.
PRECAUTIONS:
DO NOT USE THIS PRODUCT
WITHOUT READING THE MSDS SHEET AND LABEL. DO NOT ALLOW THIS MATERIAL TO
FREEZE. DO NOT STORE MATERIAL BELOW 38 DEGREES F OR ABOVE 125 DEGREES F.
SHELF LIFE 6 TO 12 MONTHS IN UNOPENED CONTAINER.
PACKAGING:
5 GALLON PAILS/55 GALLON
DRUMS
Return to
Top
HYDROSHEILD 20
TECHNICAL
DATA SHEET
HYDROSHIELD 20
CLEAR, NON GLOSS
PROTECTIVE COATING TO SEAL CONCRETE, MASONRY OR STUCCO.
PURPOSE:
HYDROSHIELD 20
HAS BEEN PRIMARILY DESIGNED TO SEAL CONCRETE SLABS, DECKS, WALLS, AND
ABUTMENTS FROM BOTH WATER AND CHLORIDE INTRUSION WHILE PROVIDING FOR WATER
VAPOR TRANSMISSION (BREATHABILITY).
THE HYDROSHIELD 20
SYSTEMS CONSISTS OF TWO COAT (SYNERGISTIC) APPLICATION PROCESS. THE PRIME
COAT IS AN OLIGOMERIC ALKOXY-SILANE WHICH CHEMICALLY BONDS TO THE
SUBSTRATE BY REACTING WITH MOISTURE EITHER PRESENT IN THE SUBSTRATE OR IN
THE ATMOSPHERE. THE HIGHLY HYDROPHOBIC CHEMICAL MOLECULES ARE EXTREMELY
SMALL (17A) RESULTING IN PENETRATION DEPTHS OF 1/4 OF AN INCH. THIS
MATERIAL IS UV RESISTANT WAND WILL NOT TURN YELLOW, AND PROVIDES A BARRIER
TO DESTRUCTIVE CARBONATION.
HYDROSHIELD 20
IS 100% OLIGOMERIC ALKOXY-SILANE MATERIALS.
ADVANTAGES:
l MARKEDLY REDUCES WATER AND CHLORIDE INTRUSION
l BREATHABLE PROVIDING FOR WATER VAPOR TRANSMISSION
l CHEMICALLY RESISTANT TO ICE MELTING COMPOUNDS, FUELS, OILS AND
ATMOSPHERIC CONTAMINANTS
l INHIBITS EFFLORENCE
l INCREASES FREEZE-THAW RESISTANCE
l PREVENTS STAINING AND DISCOLORATION DUE TO ELECTROSTATIC ATTRACTION OF
DUST PARTICLES
l CAN BE APPLIED TO DAMP SURFACES
l DEEP PENETRATION INTO SUBSTRATE
l PROVIDES A BARRIER TO DESTRUCTIVE CARBONATION
SURFACE
PREPARATION:
THE SUBSTRATE SHOULD
BE STRUCTURALLY SOUND AND FREE OF GREASE, OIL, SEALERS, COATINGS OR OTHER
SURFACE CONTAMINANTS. HYDROSHIELD 20 MAY BE APPLIED TO DAMP
SURFACES PROVIDED NO SURFACE LIQUID EXISTS.
APPLICATION:
HYDROSHIELD 20
CAN BE APPLIED DIRECTLY FROM THE
CAN, NO THINNING. THE PRIME COAT OF THE HYDROSHIELD 20 SHOULD BE
ALLOWED TO DRY FOR AT LEAST ½ HOUR BEFORE THE TOP COAT IS APPLIED.
HYDROSHIELD 20
APPLICATION COVERAGE
PRIME
COAT........................................................................................100
SQ. FT PER GALLON
TOP
COAT.............................................................................................200
SQ. FT PER GALLON
HYDROSHIELD
20...................................................................100-125
SQ FT PER GALLON
THEY MAY BE EITHER
SPRAYED OR ROLLER APPLIED
APPEARANCE:
THE HYDROSHIELD 20
SYSTEM WILL SLIGHTLY DARKEN THE SURFACE APPEARANCE OF THE SUBSTRATE IT IS
APPLIED TO. HYDROSHIELD 20 WILL NOT ALTER EITHER THE COLOR OR
TEXTURE OF THE SURFACE.
ADHESION OF
SEALANTS:
ALL CONTROL, CRACK AND
EXPANSION JOINT SEALING SHOULD BE DONE PRIOR TO THE APPLICATION OF THE
HYDROSHIELD 20.
APPLICATION:
DO NOT APPLY IN DIRECT
SUNLIGHT WHEN TEMPERATURE IS OVER 90 DEGREES F. DO NOT APPLY PRIME COAT
WHEN AIR OR SURFACE TEMPERATURE IS BELOW 15 DEGREES F. DO NOT APPLY TOP
COAT OF THE HYDROSHIELD 20 SYSTEM WHEN AIR OR SURFACE TEMPERATURE IS
BELOW 40 DEGREES F.
PRECAUTIONS:
DO NOT USE THIS PRODUCT
WITHOUT READING THE MSDS SHEET AND LABEL.
PACKAGING:
5 GALLON PAILS/55 GALLON
DRUMS
HYDROSHEILD 40
TECHNICAL
DATA SHEET
HYDROSHIELD 40
CLEAR, NON GLOSS
PROTECTIVE COATING TO SEAL CONCRETE, MASONRY OR STUCCO.
PURPOSE:
HYDROSHIELD 40
HAS BEEN PRIMARILY DESIGNED TO SEAL CONCRETE SLABS, DECKS, WALLS, AND
ABUTMENTS FROM BOTH WATER AND CHLORIDE INTRUSION WHILE PROVIDING FOR WATER
VAPOR TRANSMISSION (BREATHABILITY).
THE HYDROSHIELD 40
SYSTEMS CONSISTS OF TWO COAT (SYNERGISTIC) APPLICATION PROCESS. THE PRIME
COAT IS AN OLIGOMERIC ALKOXY-SILANE WHICH CHEMICALLY BONDS TO THE SUBSTRATE
BY REACTING WITH MOISTURE EITHER PRESENT IN THE SUBSTRATE OR IN THE
ATMOSPHERE. THE HIGHLY HYDROPHOBIC CHEMICAL MOLECULES ARE EXTREMELY SMALL
(17A) RESULTING IN PENETRATION DEPTHS OF 1/4 OF AN INCH. THIS MATERIAL IS
UV RESISTANT WAND WILL NOT TURN YELLOW, AND PROVIDES A BARRIER TO
DESTRUCTIVE CARBONATION.
HYDROSHIELD 40
IS 100% OLIGOMERIC ALKOXY-SILANE MATERIALS.
ADVANTAGES:
l MARKEDLY REDUCES WATER AND CHLORIDE INTRUSION
l BREATHABLE PROVIDING FOR WATER VAPOR TRANSMISSION
l CHEMICALLY RESISTANT TO ICE MELTING COMPOUNDS, FUELS, OILS AND
ATMOSPHERIC CONTAMINANTS
l INHIBITS EFFLORENCE
l INCREASES FREEZE-THAW RESISTANCE
l PREVENTS STAINING AND DISCOLORATION DUE TO ELECTROSTATIC ATTRACTION OF
DUST PARTICLES
l CAN BE APPLIED TO DAMP SURFACES
l DEEP PENETRATION INTO SUBSTRATE
l PROVIDES A BARRIER TO DESTRUCTIVE CARBONATION
SURFACE
PREPARATION:
THE SUBSTRATE SHOULD BE
STRUCTURALLY SOUND AND FREE OF GREASE, OIL, SEALERS, COATINGS OR OTHER
SURFACE CONTAMINANTS. HYDROSHIELD 40 MAY BE APPLIED TO DAMP SURFACES
PROVIDED NO SURFACE LIQUID EXISTS.
APPLICATION:
HYDROSHIELD 40
CAN BE APPLIED DIRECTLY FROM THE CAN, NO
THINNING. THE PRIME COAT OF THE HYDROSHIELD 40 SHOULD BE ALLOWED TO
DRY FOR AT LEAST ½ HOUR BEFORE THE TOP COAT IS APPLIED.
HYDROSHIELD 40
APPLICATION COVERAGE
PRIME
COAT.........................................................................................100
SQ. FT PER GALLON
TOP
COAT..............................................................................................200
SQ. FT PER GALLON
HYDROSHIELD
40...................................................................100-125
SQ FT PER GALLON
THEY MAY BE EITHER
SPRAYED OR ROLLER APPLIED
APPEARANCE:
THE HYDROSHIELD 40
SYSTEM WILL SLIGHTLY DARKEN THE SURFACE APPEARANCE OF THE SUBSTRATE IT IS
APPLIED TO. HYDROSHIELD 40 WILL NOT ALTER EITHER THE COLOR OR TEXTURE
OF THE SURFACE.
ADHESION OF
SEALANTS:
ALL CONTROL, CRACK AND
EXPANSION JOINT SEALING SHOULD BE DONE PRIOR TO THE APPLICATION OF THE
HYDROSHIELD 40.
APPLICATION:
DO NOT APPLY IN DIRECT
SUNLIGHT WHEN TEMPERATURE IS OVER 90 DEGREES F. DO NOT APPLY PRIME COAT WHEN
AIR OR SURFACE TEMPERATURE IS BELOW 15 DEGREES F. DO NOT APPLY TOP COAT OF
THE HYDROSHIELD 40 SYSTEM WHEN AIR OR SURFACE TEMPERATURE IS BELOW 40
DEGREES F.
PRECAUTIONS:
DO NOT USE THIS PRODUCT
WITHOUT READING THE MSDS SHEET AND LABEL.
PACKAGING:
5 GALLON PAILS/55 GALLON
DRUMS
|
